A.    For AutoCAD 11/DOS, 12/DOS or 13/DOS,  use the AutoCAD ADI  Driver
      shipped with the printer. (Driver is contained in the TechJET Personal 
      5017 Install disk. Refer to COMMON PART NUMBERS for part number).

B.    For other DOS-based CAD software, perform the following:
      
      1.    In the application, select one of the following:
            
            a.    A CalComp pen plotter driver (sometimes listed as 907/PCI,
                  or sometimes listed by model: 104x, 102x, 20xx, 30xx).
            
            b.    An HPGL driver (sometimes listed as HPGL-L with supported
                  models such as HP7580, HP7585, HP7595 or HPGL-S with
                  supported models such as HP7440).
      
      2.    Plot the drawing to a file on disk. Exit from the application.
      
      3.    Execute the TJPLOT program that was shipped with the printer to
            output the file to the printer.  (Execute the program from the
            TJPLOT directory).
      
      4.    For more details, refer to the Software Guide, chapter 3 and on
            FaxBack (document 4002).

C.    For all other DOS-based software (non CAD) where a CalComp TechJET
      Personal driver is not available, use one of the two methods:
      
      1.    The CalComp TechJET Personal printer has two modes established at
            power on, based upon the DIP switch settings.
            
            a.    The DIP switches are located next to the Power button on
                  the printer, under the plastic cover. The cover hinges
                  toward the front of the printer.
            
            b.    When a DIP switch is to be changed, first turn off the
                  printer power, change the DIP switch(es), and turn on the
                  printer power.
            
            c.    Select one of the following drivers:
                  
                  i.    When DIP switch 12 on the printer is up (normal
                        mode), select either a Canon BJ-230, BJ-200, BJ-20,
                        BJ-10ex/10e; IBM Proprinter XL24E, X24E.
                  
                  ii.   If no drivers are available from the above list, the
                        printer will accept Epson drivers when DIP switch 12
                        is down.
                        
                        ii.1. If the application has Epson LQ-1050, LQ-2550,
                              or LQ-510 driver selections, then make sure
                              that the DIP switch setting is made while the
                              printer is off, and then use one of these
                              drivers.
                        
                        ii.2. Be sure to reset DIP switch 12 to the up
                              position when attempting to use TJPLOT or the
                              CalComp TechJET Personal drivers.
            
            d.    For more information, refer to the User's Guide pages 1-16
                  and  4-2.
      
      2.    Use the TJPLOT program (shipped with the printer).
            
            a.    In the application, select a postscript driver.
            
            b.    Plot the drawing to a file on disk. Exit from the
                  application.
            
            c.    Execute the TJPLOT program that was shipped with the
                  printer to output the file to the printer. (Execute the
                  program from the TJPLOT directory).
            
            d.    For more details, refer to the Software Guide, chapter 3.

D.    For AutoCAD 12/Windows (3.x, 95, NT), use the AutoCAD 12/Windows 
      driver shipped with the printer. (Driver is contained in the TechJET 
      Personal 5017 Install disk, part number K0103-970).


E.    For AutoCAD 13/Windows (3.x, 95, NT), use the TechJET Personal 
      AutoCAD 13/Windows ADI Driver. The file is available on the CalComp Web Site       http://www.calcomp.com. The filename is TJACAD13.EXE.

      For AutoCAD 14/Windows 95 use the System Printer, set for a BJ-230 printer.

F.    For Windows 3.x based software other than AutoCAD 13/WIN,
      use the TechJET Personal Windows driver shipped with the printer.
      (Driver is contained in the TechJET Personal 5017 Install disk, 
      part number K0103-970).

      Note: If a driver is needed for Windows 3.1 based software, including 
      AutoCAD 13/WIN, it is available on the CalComp  Web Site 
      http://www.calcomp.com. The filename is TJWIN31.EXE.

G.    For Windows 95 based software other than AutoCAD 13/WIN,
      use the Canon BJ-230 Windows-95 driver. The driver is included with
      Windows 95. 

H.    For Windows NT based software other than AutoCAD 13/WIN,
      use the Canon BJ-230 Windows-NT driver. The driver is included with
      Windows NT.

I.    For Unix-based systems, our drivers work on the Sun OS.  For more
      information, refer to the Software Guide, chapter 5.

J.    There are no drivers available for the Macintosh.  

K.    The TechJET Personal software is shipped with the printer. Except where
      noted herein, it is not available on the Web. 
      (Refer to COMMON PART NUMBERS for part number).