What does the 67436 plotter emulate?

A.   WHAT PLOT COMMAND LANGUAGES DO THE 67436 PLOTTERS SUPPORT:

     These plotters have 4 plot data ports (2 serial and 2 parallel).
     The port marked TERMINAL CANNOT be used for plot data.

     1.   907/PCI/CCGL (supported on all 4 plot data ports)
          The standard or native CalComp vector plot command language.
          The best choice for most CAD applications.

     2.   HPGL (supported on all 4 plot data ports)
          The standard Hewlett-Packard pen plotter language for both
          small and large format HP pen plotters.

          Plotter Setup Tips (using a terminal and OPCOM):
          In the port configuration menu for the plotter, at the Plot
          Command Language prompt, enter HPGL. Then select the default
          (CLCMP) at the next prompt, for Plotter Emulation Type, or,
          for large format HP emulation, enter a Plotter Emulation Type
          of either the 7585A or 7585B (both work the same).

          CLCMP works best for small format HP plotter drivers, such as
          the 7475 or 7550.

     3.   HP/GL2 (supported on all 4 ports; REQUIRES firmware revision
          4.05 or greater)

          The 67436 emulates the HP 7600. In the plotter's port
          configuration, first select HPGL as the Plot Command Language.
          Then enter 7600 for the Plotter Emulation Type.

     4.   CCRF (supported on the parallel ports only)
          The CalComp Raster Format for large format (D and E size)
          plotters. 67436 plotters support BOTH compressed and
          uncompressed CCRF data.

          a.   The 67436 supports CCRF data in both Direct and Buffered
               modes.

          b.   The 67436 requires firmware revision 3.16 or greater to
               support 'Non-Sticky' CCRF. Non-sticky CCRF means that as
               soon as the CCRF file is printed, the CalComp port
               configuration reverts back to it's initial setting.

B.   WHAT EMULATION UPGRADE OPTIONS ARE AVAILABLE:

     1.   POSTSCRIPT:  (parallel ports only) The CalComp model 86625
          Print Bridge may be used as an external interface to the 67436
          plotter, converting PostScript data into CCRF raster data
          (PostScript Level 2 is NOT supported).

     2.   CGM  (Computer Graphics Metafile, supported on all data ports)

          CGM is an optional plotter firmware upgrade. It is not
          available as one of the plotter's standard features. To
          purchase the CGM enhancement, contact CalComp's order line at
          1-800-225-2667 and ask for the CGM Firmware Upgrade Option.
          The CGM enhancement requires a minimum firmware 3.16. (4.05
          recommended).


     3.   VERSATEC/GREENSHEET:  (parallel ports only) CalComp's model
          914 Versatec external interface box IS SUPPORTED.

C.   WHAT COMMONLY USED LANGUAGES (EMULATIONS) ARE NOT  
       SUPPORTED:

     1.   POSTSCRIPT  LEVEL 2

     2.   HP/RTL (not supported)

     3.   TIFF  (not supported)

     4.   CALSG4  (not supported)


D.   WHAT IS THE 907/PCI LANGUAGE?

     1.   907/PCI/CCGL is the native CalComp plot command language. It
          is a vector-based format and is therefore very efficient for
          CAD applications. It is the plot language of choice for most
          if not all CAD programs. 907/PCI/CCGL is most often referred
          to as 907 (or 907/PCI). CCGL stands for CalComp Color Graphics
          Language.

     2.   By strict definition, the 907/PCI format is the complete
          command set for a CalComp pen plotter.

          CCGL is a superset of 907/PCI and includes additional
          (extended) commands which are supported by all CalComp large-
          format raster products. The 67436 is part of this family of
          CalComp plotters.

          This extended set basically ADDS pen definition and
          color/pattern definition commands to the existing 907/PCI
          language.


E.   WHAT IS THE CCRF LANGUAGE?

     CCRF means CalComp Raster Format. It was specifically designed for
     CalComp's large format raster plotters. It is best used when
     graphic images need to be printed, as opposed to CAD files.

     1.   DIRECT MODE (Faster plot time and unlimited file size)

          In this mode, the plotter prints the CCRF file as it is
          received. Generally, there is no limit to the size of the CCRF
          file to be printed when you are using DIRECT MODE.

     2.   BUFFERED MODE  (Slowest initial plot time but very fast
          replot. Limited file size)

          In this mode, the plotter stores the CCRF file onto it's hard
          disk before printing it. Therefore, a particular CCRF file (or
          group of CCRF files) cannot exceed the size (or available
          space) of the plotter's hard disk.

          The available space is determined by the number of USER files
          that have been created (each one uses about 60k of space) and
          the number of vector or buffered CCRF files which have been
          sent to the plotter and automatically stored for replot (All
          vector jobs are automatically stored on the plotter"s disk,
          they don't have a Buffered or Direct mode).

          BUFFERED MODE allows you to replot the CCRF file as many times
          as you like (until the plotter is powered off, then all jobs
          that were stored will be deleted).

     3.   COMPRESSED AND UNCOMPRESSED CCRF DATA
          Uncompressed CCRF files can be much larger than compressed
          CCRF files, but usually plot quite a bit faster. The reason
          for this is that compressed CCRF files must be uncompressed by
          the plotter before it can print them.